Osmo Polyx-Oil Rapid 3262 Clear Matt

Osmo Polyx-Oil Rapid 3262 Clear Matt

Osmo Polyx-Oil Rapid 3262 is a fast-drying clear matt oil and wax finish for interior wooden floors and furniture. Its combination of natural plant oils and waxes provides hard-wearing, water-repellent and easy-to-maintain protection.

The matt sheen diffuses light reflections and gives the wood a calm, almost natural appearance while leaving the grain and texture visible. However, the natural oils still enhance the colour of the timber, making pale wood species appear warmer and slightly darker.

Under suitable conditions, two very thin coats can be applied in one day.

Suitable applications

Osmo Polyx-Oil Rapid 3262 is suitable for:

• Solid wood flooring

• Parquet flooring

• Plank flooring

• Engineered flooring with a suitable real-wood wear layer

• Strip flooring

• OSB flooring

• Cork flooring

• Wooden stairs

• Solid wooden furniture

• Other untreated interior wooden surfaces

Always carry out a trial application on unfamiliar wood species, existing finishes and factory-finished flooring.

Difference between 3262 Matt and 3232 Satin

Both 3262 and 3232 belong to the fast-drying Osmo Polyx-Oil Rapid range. Their main difference is the final sheen:

• 3262 Clear Matt: calm appearance with minimal light reflection

• 3232 Clear Satin: subtle satin sheen

Both finishes enhance the natural colour of the wood. Matt therefore does not mean that treated timber will retain exactly the same pale appearance as untreated wood.

Not intended for concrete or stone

Osmo Polyx-Oil Rapid 3262 is designed for wood, OSB and cork. Do not use it to impregnate concrete, tiles, screed or other mineral surfaces.

For absorbent interior concrete and stone, use Osmo Concrete Oil 610.

For absorbent exterior stone and terracotta, use Osmo Stone and Terracotta Oil 620.

Benefits of Osmo Polyx-Oil Rapid 3262

• Clear matt finish

• Fast-drying version of Osmo Polyx-Oil

• Two thin coats can be applied in one day

• Suitable for wooden flooring, parquet, OSB, cork and furniture

• Hard-wearing and water-repellent

• Dirt and stain resistant

• Resistant to common liquid spillages

• Microporous and breathable

• Will not crack, peel, flake or blister

• No primer normally required on untreated wood

• No sanding required between coats

• Can be repaired locally

• Approximately 24 m² coverage per litre with one coat

• Approximately 4–5 hours drying time per coat under suitable conditions

• Available in 0.75, 2.5, 10 and 25 litre containers

Resistance to common liquids

Once fully cured, Osmo Polyx-Oil Rapid is resistant to:

• Water

• Wine and beer

• Cola

• Coffee and tea

• Fruit juice

• Milk

The finish meets DIN 68861-1A/EN 12720 for resistance to these liquids. Nevertheless, wipe up spillages as soon as possible to prevent prolonged exposure and potential discolouration.

Once dry, the finish is resistant to saliva and perspiration according to DIN 53160 and suitable for children’s toys according to EN 71.3.

Matt does not mean colour-invisible

Osmo 3262 is clear and matt, but it still contains natural oils. These oils enhance the natural tone of the wood and create a permanent wet-look effect.

Oak, pine, beech and other pale timbers will normally become warmer and deeper in colour. If you want to retain a very pale appearance similar to untreated wood, select a specially formulated Natural or Raw finish instead.

Always prepare a trial area using the same sanding and application method intended for the final surface.

Preparing the wood

The wooden surface must be:

• Clean and completely dry

• Free from dust, grease and dirt

• Free from old paint, lacquer and closed-film coatings

• Frost-free

• At a maximum moisture content of 18%

Thoroughly clean old microporous oil and hardwax-oil surfaces. Completely remove old paint and lacquer coatings.

Fill small areas of damage and screw holes with a suitable wood filler. Fixed small parquet joints can be filled with a compatible sanding-dust joint filler.

Sanding wooden flooring

Sand the complete surface carefully and evenly. Differences in sanding grit can become visible after oiling as variations in colour or sheen.

For wooden flooring, the final sanding stage is normally:

• P100 for slightly stronger colour enhancement and more surface texture

• P120 for a calmer and more even appearance

For furniture, use a final grit of approximately P120–180, depending on the timber and desired appearance.

Thoroughly remove all sanding dust with a vacuum cleaner and suitable dust cloth. Always wear an appropriate dust mask while sanding.

Applying Osmo Polyx-Oil Rapid 3262

Osmo Polyx-Oil Rapid is ready to use and must not be diluted. Stir thoroughly before and during application with a flat stirring stick or spatula.

Apply the first coat very thinly and evenly along the wood grain. Use a suitable microfibre roller, floor brush or flat brush.

For the best result, use the specialist rollers, floor brushes and flat brushes shown among the related products below. These tools have been selected to distribute Polyx-Oil in a thin and controlled layer.

An unsuitable roller or coarse brush may deposit excessive material, causing streaks, uneven sheen and substantially extended drying times.

Spread the oil thoroughly within 10–15 minutes and remove all accumulations and excess material. No thick or visibly wet areas should remain.

Applying the second coat on the same day

Allow the first coat to dry for approximately 4–5 hours under normal conditions with good ventilation.

Only apply the second coat when the first coat feels completely dry across the entire surface. Low temperatures, high humidity, insufficient ventilation or excessive application will extend the drying time.

Apply the second coat equally thinly and evenly. Sanding between coats is normally unnecessary.

Although two coats can be applied in one day under suitable conditions, never apply the second coat over a damp or tacky first coat.

Full curing time

The floor can be walked on carefully after drying, but the finish has not yet fully cured. Complete curing takes approximately 2–3 weeks.

During this period:

• Do not cover the surface with plastic, cardboard or rugs

• Provide good ventilation

• Wipe up water and spillages immediately

• Do not damp mop the floor

• Avoid heavy use and intensive cleaning

• Position furniture carefully without dragging it

Wait until the finish has fully cured before placing rugs or other impermeable coverings.

Dark and extractive-rich hardwoods

Polyx-Oil Rapid may be less suitable for dark, extractive-rich hardwoods such as wenge, merbau and jatoba.

For these species, use Osmo Wood Wax Finish Clear Extra Thin or carry out an extensive trial application first. Natural wood extractives may influence adhesion, drying and final appearance.

Application on cork

Cork is highly absorbent. Apply Osmo Polyx-Oil Rapid especially thinly to cork surfaces.

Allow for a longer drying time of at least 6–8 hours per coat. Always prepare a trial area to assess product consumption and final appearance.

Coverage

One litre of Osmo Polyx-Oil Rapid 3262 covers approximately 24 m² with one thin coat on smooth, planed or carefully sanded wood.

Actual coverage depends on:

• Wood species

• Absorbency of the wood

• Sanding preparation

• Condition of the surface

• Application method

• Applied film thickness

Rough, coarsely sanded or highly absorbent wood requires more product.

Cleaning and maintenance

Regularly remove dust and loose dirt with a soft broom, vacuum cleaner or suitable dust mop.

For regular weekly hygienic cleaning, use our Eco Multi Cleaner. Damp mop the floor and never leave standing water on the wood.

Use Osmo Wash and Care additionally when the oil and wax finish requires conditioning. It should not replace regular hygienic cleaning.

For periodic refreshing and local treatment of light wear, use Osmo Liquid Wax Cleaner 3029. Be aware that polishing may locally increase the sheen of an originally matt floor.

When visible wear develops, thoroughly clean the surface and apply one very thin maintenance coat of Polyx-Oil Rapid 3262. One coat is normally sufficient when renovating an intact, previously oiled surface.

View the Osmo maintenance plan

Cleaning tools and working safely

Clean brushes, rollers and other tools immediately after use with Osmo Brush Cleaner and Thinner.

The liquid and vapour are flammable. Keep away from heat, sparks and open flames. Do not smoke during application.

Cloths and pads saturated with liquid oil may generate heat and ignite spontaneously. Lay them flat outdoors to dry completely or place them immediately in a suitable airtight metal container.

Keep out of reach of children and provide good ventilation during application, drying and curing.

Technical information

• Download the official Osmo Polyx-Oil Rapid product information
  
  
• Osmo Polyx-Oil Rapid – Safety Data Sheet (PDF)