Primer 7000 White – fast-drying white base coat for exterior wood
(excl. btw €66,07)
Osmo Primer 7000 White is a fast-drying base coat for exterior wood receiving a white or light-coloured opaque finish. Practical for preparing wooden components before installation.
- Ordered before 17:00:00, delivered tomorrow
- Altijd de laagste prijs (Minimaal 40% korting op de winkelprijs)
- Kies zelf uw verzendwijze.
- Achteraf betalen met Klarna
- More information? Contact us about this product
Osmo Exterior Primer 7000 White
Osmo Exterior Primer 7000 White is a quick-drying, opaque white base coat for exterior timber. It creates an even white foundation for a subsequent white or light-coloured opaque exterior finish.
The primer is particularly useful as a first coat before installation. Timber can be prepared in the workshop, allowing edges, end grain, reverse faces and other areas that may become difficult to reach after assembly to be treated properly.
Osmo Exterior Primer is strongly drip-resistant and has been developed for quick, controlled application with a suitable brush or microfibre roller.
Benefits of Osmo Exterior Primer 7000 White
-
Opaque white primer for exterior timber
-
Ideal for application before installation
-
Creates an even base beneath light finishing colours
-
Quick drying in approximately 4–5 hours
-
Strongly drip-resistant
-
Ready to use and must not be diluted
-
Covers approximately 12 m² per litre
-
Requires one thin primer coat
-
Suitable for dimensionally stable and non-dimensionally stable timber
-
Suitable for brush or microfibre roller application
-
Tools can be cleaned with soap and water
-
Suitable for professional and private use
Suitable applications
Osmo Exterior Primer 7000 White can be used on:
-
Timber cladding
-
Roof soffits and fascia boards
-
Rafters and purlins
-
Balconies
-
Fences and screens
-
Pergolas and covered structures
-
Garden buildings
-
Carports
-
Window frames and other timber components
-
Dimensionally stable and non-dimensionally stable exterior timber
The primer is intended for projects that will receive a white or light-coloured opaque final finish.
Selecting the final finish
Osmo Exterior Primer 7000 White is a base coat only and must not be left as the final exterior finish.
Once dry, finish the primer with a suitable white or light-coloured opaque exterior coating, such as:
-
Osmo Opaque White Gloss
-
Osmo Country Colour
-
Another compatible white or light-coloured opaque Osmo exterior finish
A dark or transparent finish is not a logical choice over this opaque white primer. When using another coating system, always perform a trial application to check adhesion, drying and the final appearance.
Surface preparation
The wood must be clean, dry, frost-free and free from dust, grease and loose previous coatings.
Observe the following conditions:
-
Minimum application and surface temperature: +4°C
-
Maximum timber moisture content: 18%
-
Completely remove old closed-film paints and varnishes
-
Clean intact microporous finishes thoroughly
-
Remove all sanding dust
-
Wear a suitable dust mask during sanding
The timber species and condition of the surface influence colour, coverage and adhesion. Always perform a trial application, especially on unfamiliar wood species or existing coatings.
Timbers rich in natural extractives, including Oak, Robinia and Larch, may release coloured substances during weathering. Allow these woods to weather first where necessary and test the complete coating system before starting the project.
Optional preservative pre-treatment
If additional preventive protection against wood-discolouring or wood-destroying fungi is required, first treat the bare timber with a suitable Osmo WR preservative.
Where possible, apply the preservative to all sides and allow it to dry completely in accordance with its product instructions before applying Exterior Primer 7000.
A preservative is a separate pre-treatment and does not replace either the primer or the final exterior coating.
Applying Osmo Exterior Primer 7000 White
Stir the product thoroughly before and during use. The primer is ready to use and must not be thinned.
Apply one thin, even coat in the direction of the wood grain. When treating timber before installation, coat all sides wherever possible. Pay particular attention to edges, joints and end grain.
For an even professional result, use our recommended flat brushes or microfibre application rollers shown among the related products below.
A suitable roller distributes the primer in a thin, even coat without creating unnecessary surface texture or heavy local deposits. Do not use a coarse roller intended for wall paint.
Coverage and drying time
-
Required primer coats: 1
-
Coverage: approximately 12 m² per litre
-
Drying time: approximately 4–5 hours
-
Reference conditions: 20–23°C and 50–65% relative humidity
-
Minimum application temperature: +4°C
-
Maximum timber moisture content: 18%
-
Colour: 7000 Opaque White
Actual coverage depends on timber species, absorbency and surface structure. Rough or highly absorbent wood may require more product than smooth, planed or sanded timber.
Ensure good ventilation during drying. Lower temperatures or higher humidity can significantly increase the drying time.
Cleaning and storage
Clean brushes and rollers with soap and water immediately after use.
Close the container carefully and store it in a cool, dry and frost-free location. Protect it from temperatures above 30°C and keep it out of reach of children.
Safety information
The product contains preservatives and may cause an allergic reaction. Do not allow it to enter soil, drains or surface water.
Always read the label and current safety data sheet before use. Dispose of product residue according to local regulations.
Technical information
| Brand | Osmo |
| Article code | 14626 |