3062 Hard wax oil colorless MAT

Osmo Polyx-Oil Original 3062 Clear Matt

Osmo Polyx-Oil Original 3062 is a clear matt finish for wooden floors, furniture and other interior wooden surfaces. Its combination of natural vegetable oils and waxes protects the wood against dirt, moisture and everyday wear while allowing the natural grain and texture to remain visible and tangible.

The oils penetrate the wood while the waxes protect the surface. This creates a durable, water- and dirt-repellent finish that will not crack, flake, blister or peel. Colour 3062 gives the wood a calm, matt appearance with minimal surface sheen.

Please note: clear does not mean invisible. Osmo Polyx-Oil 3062 enhances the natural colour of the wood and produces a slight permanent “wet look”. If you want light oak to retain an appearance closer to untreated wood, choose Osmo Polyx-Oil Effect Natural 3041 or Raw 3044 instead. Always carry out a test application first.

Benefits of Osmo Polyx-Oil 3062

• Clear finish with a matt appearance

• Suitable for wooden floors, furniture, stairs and other interior wood

• Based on natural vegetable oils and waxes

• Highly water- and dirt-repellent

• Hard-wearing and suitable for frequently used surfaces

• Resistant to water, coffee, tea, milk, fruit juice, cola, beer and wine

• Microporous finish that will not crack, flake, blister or peel

• No separate primer or intermediate sanding required

• Easy to maintain, refresh and renovate locally

• Saliva- and perspiration-resistant once dry

• Suitable for children’s toys according to EN 71.3 once dry

• Coverage: approximately 24 m² per litre per coat

• Drying time: approximately 8–10 hours per coat

• Fully cured after approximately 2–3 weeks

Difference between 3062 Matt and 3032 Satin

Osmo 3062 produces a matt appearance and reflects less light than Osmo Polyx-Oil 3032 Clear Satin.

On dark woods, dark-coloured floors or very dark stained surfaces, the matting agents in 3062 may occasionally create a light or powdery haze. Always test the finish on a small area first.

If you require a low-sheen finish on dark wood but want to reduce the risk of a light haze, Osmo 3065 Clear Semi-Matt may be a better choice.

Suitable surfaces

Osmo Polyx-Oil Original 3062 is suitable for:

• Solid wooden floors

• Parquet and floorboards

• Country-style and ship-deck flooring

• OSB flooring

• Cork flooring

• Wooden stairs

• Furniture and table tops

• Other interior wooden surfaces

Dark, ingredient-rich hardwoods such as wenge, merbau and jatoba may absorb this product differently. For these woods, we recommend Osmo Clear Wax 1101. Always test the product on unfamiliar wood species or existing finishes.

Use the correct rollers and brushes

Apply Osmo Polyx-Oil very thinly and evenly. The application tool has a major influence on the final result. We therefore recommend using the specialist rollers, floor brushes, pads and cloths displayed as related products at the bottom of this page.

Recommended tools include:

• Special oil and hardwax-oil roller

• 25 cm roller with frame

• Mini rollers with frame

• Osmo floor brush

• Special Osmo brushes

• Tisa Line flat brush

• Cotton cloths for removing excess oil

• Rectangular application and polishing pads

Avoid using an unsuitable general-purpose roller. The wrong roller or brush may apply too much product and cause visible overlaps, streaks, uneven sheen or considerably longer drying times.

Surface preparation

The wooden surface must be clean, dry and frost-free. The moisture content of the wood must not exceed 18%.

Osmo Polyx-Oil 3062 is ready to use:

1. Stir thoroughly before and during application.

2. Do not dilute the product.

3. Completely remove old paint and lacquer coatings.

4. Thoroughly clean existing microporous oil finishes.

5. Fill small cracks and holes with a suitable wood filler where necessary.

6. Finish-sand wooden floors with P120–150 grit.

7. Finish-sand furniture with P180–240 grit.

8. Carefully remove all sanding dust with a vacuum cleaner.

The final appearance depends on the wood species, surface structure, sanding process and quantity applied. Always carry out a test application first.

Applying Osmo Polyx-Oil 3062

Apply the first coat very thinly and evenly in the direction of the wood grain using a suitable roller, floor brush, flat brush or application pad. Spread the product carefully and avoid thick coats or puddles.

Allow the first coat to dry for approximately 8–10 hours with good ventilation. Then apply a second, equally thin coat.

Two thin coats are normally required on untreated or bare-sanded wood. When renovating an existing Osmo oil finish, one thin coat on a clean, dry and intact surface is usually sufficient.

Complete sanding is often unnecessary during normal maintenance. If the existing finish is damaged, sealed, contaminated or unsuitable for recoating, more extensive preparation will be required.

Coverage and drying time

• Coverage: approximately 24 m² per litre per coat

• Untreated wood: two thin coats

• Renovation: usually one thin coat

• Drying time: approximately 8–10 hours per coat at 23°C and 50% relative humidity

• Fully cured: after approximately 2–3 weeks

Actual coverage depends on the wood species, structure, absorption and preparation. Rough or highly absorbent wood will require more product.

Apply particularly thin coats to cork and allow at least 24 hours of drying time per coat. Applying too much product, insufficient ventilation, low temperatures or high humidity can considerably extend the drying time.

Special applications

For light oak where you want to retain an appearance close to untreated wood, we recommend Osmo Polyx-Oil Effect Natural 3041 or Raw 3044.

A clear topcoat may make white or white-pigmented surfaces appear warmer or more yellow. Use a suitable white-pigmented Osmo topcoat on these surfaces.

For certain dark or ingredient-rich tropical hardwoods, we recommend Osmo Clear Wax 1101.

If you intend to apply 3062 Matt over a coloured finish, always test it first. The matting agents may create a light haze, particularly on dark colours.

Cleaning and maintenance

Regularly remove sand and loose dirt with a soft broom or vacuum cleaner.

Use our Eco Multi Cleaner with a well-wrung mop for normal weekly cleaning. Use as little water as possible and never allow puddles to remain on the wood.

Use Osmo Wash and Care periodically when the floor requires additional care and nourishment. Osmo Liquid Wax Cleaner can be used to refresh dull areas or minor signs of wear.

Follow the HardwaxStore.nl Osmo maintenance plan for the correct combination and frequency of cleaning and maintenance products.

Do not use aggressive all-purpose cleaners, chlorine, bleach, baking soda or strongly degreasing washing-up liquids. These products may damage or discolour the finish.

Important safety information

Use only in a well-ventilated area and keep out of reach of children. Avoid contact with eyes, skin and clothing. Always consult the product label and safety data sheet before use.

Warning: risk of spontaneous combustion. Cloths, pads and other materials soaked with liquid oil must be washed immediately after use or stored in an airtight metal container. Never leave oil-soaked materials crumpled together.

Sizes and sheen levels

Osmo Polyx-Oil Original 3062 Clear Matt is available in various container sizes, subject to current availability. Select the required size at the top of the product page.

The clear Original range is available in different sheen levels:

• 3011 Clear Gloss

• 3032 Clear Satin

• 3062 Clear Matt

• 3065 Clear Semi-Matt

Technical information and maintenance advice

View the Osmo Polyx-Oil brochure

Download the technical product information

View the HardwaxStore.nl Osmo maintenance plan